Deburring System
Holding System
Cooling System
Chip Hooks

Technical Support

Cooling System

which cooling solution can be used on machines without cooling ?

Date: 03-10-2005 Author: Ori Barak

The MiniCool units are totally independent units.
It works only by using air pressure.
The portable cooling unit can be mounted on the machine or on any metal surface by using the powerfull on/off magnet.

Deburring System

How to choose the right swivel blade?

Date: 02-02-2011 Author: ori barak

Click to view topic....

Noga program offers a wide comprehensive range of deburring blades.

For every type of deburring blades you can see the drawings showing the suitable applications.

You can find these drawings at the bottom left side of the page.

Please select the blade according to the drawing application were the area marked in red is the area where the blade works.

For some applications there is a selection of blades according to the workpiece material, blade material and grinding angle.

which left hand blades can be suitable for left hand users?

Date: 02-02-2011 Author: Avi Widovski

Click to view topic....

Most of the swivel blades are grinded to work clockwise (for right hand users), However left hand users can use one of the following blades:
Symmetrical blades: Like S20, N2, S202.
These blades are grinded symmetrically and can be used by right and left hand users.

Left Hand blades: Some of the popular blades are available in a special version for left hand users only. For example: S10 LH, N1 LH, N1LH TiN, S101 LH, S10 LH TiN .
.

which handle can hold needle files

Date: 18-12-2007 Author: mr. v

Click to view topic....

Noga new YT Handle is design to hold needle files. Range 2.5-4.4mm

Conversion chart for deburring program

Date: 09-01-2006 Author: Ori Barak

Click to view topic....

In the list below you can find a conversion chart for the deburring program.
Some of the items remained unchanged.
Look for the p/n that you used to buy and then you will find the alternative p/n.

Old item	Replacing p/n	Old item	Replacing p/n
EO1000	EO1000	IS1000	NG3710
EO2000	EO2000	SC8000	SC8000
RB1000	RB1000	SC4000	SC4000
SG1000	SG1000	SC5100	SC5100
NB1100	Not Avail.	CR2000	CR2000
NB3000	NG1003	CR1100	CR1100
NB5000	NG1005	NC1000	NG3200
TB1000	TB1000	NC2000	NG3220
LB1000	LB1000	NC3000	NG3210
RC1000	RC1000	NC4000	NG3230
RC2000	RC2000	KW1000	NG3300
RC2200	RC2200	LD1000	NG3800
RD1040	NG1200	DB1000	DB1000
RD4000	NG1700	KW2000	NG1100
CS1000	NG3100	TC1000	NG1600
RD7000	NG3400	SP8000	SP8000
SC1000	SC1000	SP8100	SP8100
MS1000	NG3700	RB1200	RB1400

Which set can you suggest for deburring of various holes diameter ?

Date: 24-10-2005 Author: Ori Barak

Click to view topic....

We can suggest the NG9300 - Silver Unikit. which covers the hole range from 3.2mm-16.5mm by using our patented crancked countersinks for easy deburring.
This set contains also a reversible countersink, external contersink and S10,S20,S30 swivel blades which makes it the ideal set for MRO - Maintenance Repair Operation.

Holding System

Conversion chart for the Holding Program

Date: 09-01-2006 Author: Ori Barak

Click to view topic....

In the list below you can find a coversion chart for the holding program.
Some of the items remained unchanged.
Look for the p/n that you used to buy and then you will find the alternate p/n.

Old P/N	Will be replaced by	Old P/N	Will be replaced by	Old P/N	Will be replaced by	Old P/N	Will be replaced by
NF		DG		MG		PH
NF1008	NF61003	DG2030	DG61003	MG2030	MG61003	PH3035	PH3100
NF1009	NF61003	DG2033	DG61003	MG2033	MG61003	PH3040	PH3100
NF2040	NF61003	DG2010	DG60103	MG2010	MG60103	PH3050	N.A.
NF2045	NF60103	DG2013	DG60103	MG2013	MG60103	PH3015	N.A.
NF1016	NF1022	DG2040	DG61003	MG2040	MG61003	PH2030	PH6400
NF1019	NF1022	DG2045	DG60103	MG2045	MG60103	PH2010	PH6410
NF1007	NF60103	DG1030	DG61003	MG1030	MG61003	PH4045	PH6610
NF1006	NF60103	DG1033	DG61003	MG1033	MG61003	PH4050	PH6810
NF1035	NF10403	DG1040	D.I.Y.	MG1250	D.I.Y.	PH2020	PH6400
NF1030	NO CHANGE	DG1043	D.I.Y.	MG1010	MG60103	PH2023	PH6400
NF1033	NO CHANGE	DG1010	DG60103	MG1013	MG60103	PH2000	PH6410
NF2030	NF61003	DG1013	DG60103	MG1050	MG10503	PH2003	PH6410
NF2033	NF61003	DG1035	DG61003	MG1053	MG10533	PH2035	PH6400
NF2021	NF61003	DG1038	DG61003	MG1600	D.I.Y.	PH2040	NO CHANGE
NF2024	NF61003	DG1050	DG10503	MG1100	D.I.Y.	PH2015	PH6410
NF1040	NF10403	DG1053	DG10533			PH4016	NO CHANGE
NF1043	NF10433	DG1015	DG60103	LMG
NF1021	NO CHANGE	DG1018	DG60103	MG1040	MG71003
NF1024	NO CHANGE	DG1300	D.I.Y.	MG1043	MG71003
NF1150	D.I.Y.	DG1400	D.I.Y.	MG1035	MG71003
NF1015	NO CHANGE	DG1600	D.I.Y.	MG1038	MG71003
NF1018	NO CHANGE	DG1100	D.I.Y.	MG1200	D.I.Y.
NF1010	NF60103

Which types of indicators can be held by Noga holders?

Date: 02-02-2011 Author: Avi Widovski

Click to view topic....

Noga customers are using different types of indicators, most popular are:
- European Standard - 8mm
- American Standard - 3/8"
- Japanese standard - 6mm

.The indicators can be held by dovetail, stem or back lug.
Noga Introduced its Universal swivel clamp FA1500 that can hold all sizes(6mm,8mm and 3/8").

All Noga FAT holders are equipped with the Universal swivel clamp as a standard.

Which is the smallest holder that can be used on small surfaces?

Date: 09-11-2005 Author: Ori Barak

Click to view topic....

Our smallest holder is the NF1030/1033 with a permanent magnet.
Magnet dimensions W16xL60xH32, Magnet Force 280 N.
The holder weight is 0.300Kg with arm length of 107mm.

Please refer also to attached topic at: http://www.practicalmachinist.com/cgi-bin/ubbcgi/ultimatebb.cgi?ubb=get_topic;f=1;t=015496;p=0
For more information about the product: http://www.noga.com/nogaProducts.php?prdID=NF1033

Other

Which ISO standards Noga follows

Date: 02-02-2011 Author: Ori Barak

Click to view topic....

All Noga products meet the strict requirements of ISO9001 and ISO14001.